Skip to Content

Is Your Husqvarna Lawn Mower Solenoid Bad? (Troubleshoot)

When your mower won’t turn over and you hear a clicking or humming sound, you may have a faulty solenoid. I have provided tips on how to find and identify a bad starter solenoid.

A Husqvarna starter solenoid is likely bad when the starter motor turns over the engine with the solenoid bypassed.

A starter solenoid that is mounted on the starter can be tested using a battery charger to determine whether the solenoid is bad.

Take caution when working with the starter solenoid. Follow all safety precautions listed in your Husqvarna operator’s manual to avoid injury.

Starter solenoid

This post may include affiliate links. Purchases made through these links may provide a commission for us, at no extra cost to you. As an Amazon Associate, we earn from qualifying purchases.

Follow all safety instructions provided in your equipment operator’s manual before diagnosing, repairing, or operating. Consult a professional if you don’t have the skills, or knowledge or are not in the condition to perform the repair safely.

What Is a Husqvarna Lawn Mower Solenoid? 

A Husqvarna lawn mower solenoid is an on/off switch of sorts. It is an electromagnet switch that is actuated to engage the starter motor to turn over the engine.

The starter solenoid is usually mounted to the starter motor, but it doesn’t need to be to work correctly. Some lawn mower solenoids can be found mounted closer to the battery than the starter. 

Three & Four Post Solenoids 

This is a typical wire schematic of three and four-post solenoids. Remember, not all wire schematics are the same for every lawn mower.

Some schematics will include wiring for options like lights and 12-volt ports on some Husqvarna mowers. These diagrams only show the basic wiring schematic. 

Basic lawn mower starter solenoid diagram

How to Identify Husqvarna Lawn Mower Solenoid? 

Solenoids can appear a little differently. Some may be round while others are square. It may have 3 or 4 posts sticking out of it. Some solenoids will be attached at the top of the starter.

The positive (+) wire from the Husqvarna battery attaches to one side of the solenoid. Following the positive cable from the battery is an easy way to find your solenoid.  

You will find solenoids on every Husqvarna electric start engine.  

What Causes a Husqvarna Lawn Mower Solenoid to Go Bad? 

A Husqvarna solenoid is an electrical switch. Electrical items can fail at any time.

Inside the solenoid, you will find a spring and copper plate. A Husqvarna starter solenoid can go bad if the spring gets weak or the copper plate starts to corrode.

The solenoid can also fail as a result of a weak starter, bad battery, or bad ground.  

It is good to know what to look for when you are diagnosing a solenoid. 

Symptoms of a Bad Husqvarna Solenoid on Lawn Mower 

A Husqvarna zero-turn starter solenoid may be bad if you hear a click or hum when you turn the ignition key and your mower doesn’t start.

Another indication your solenoid may be bad is when a wire gets hot and begins to smoke or melt

Steps to Diagnose a Bad Husqvarna Lawn Mower Solenoid 

List Tools Needed: 

  • Volt-Ohms Meter 
  • Screwdriver 
  • Continuity Light
  • Wrenches to check for loose wires 
  • Needle Nose Pliers (If screwdriver does not work) 
  • Battery Charger (Optional) 

If you are going to diagnose the solenoid on your lawn mower, there are a few ways to do so. 

1. Make Sure Your Battery Has a Full Charge

Use your voltmeter to make sure your battery has at least 12.3 volts in it. Read more about testing your battery in our article 5 Things That Are Draining the Life of Your Lawn Mower Battery.

2. Get Your Mower Ready to Start

  • Set the parking brake
  • Make sure your lawn mower is in neutral
  • Turn the key to the on position

3. Bypass the Starter Solenoid Using a Screwdriver

Lay a long screwdriver over the solenoid to touch the two cables to bypass the starter. The two cables you are looking for are the cable from the battery and the cable to the starter.

It may throw a spark when the screwdriver makes contact with the wires. This is common so don’t be alarmed.

If the engine happens to turn over while you have your solenoid bypassed there is a good chance your solenoid is bad. If the screwdriver does not work well, you can also use needle nose pliers to jump the solenoid. 

Before you replace the starter solenoid, check for loose or corroded wires or bad ground. These items can keep the solenoid from getting the power it requires to work. 

4. Test the Starter Solenoid

Solenoids that are mounted on the starter can be tested. Remove the starter from the engine and test the solenoid with a battery charger. This is a good way to watch if the starter is working with the solenoid. 
 
Once the starter has been removed from your lawn mower, you need to attach the negative (-) clamp to the case of the starter and touch the positive (+) clamp to the big post and exciter wire on the solenoid. This is just a quick bench test when the starter is out. 

Can You Bypass a Husqvarna Lawn Mower Starter Solenoid? 

A Husqvarna starter solenoid can be bypassed by placing a long screwdriver across the solenoid from touching the cable from the battery to the cable to the starter.

Be careful. The connection could cause a spark which is normal. Always wear safety gear.

Starter Solenoid is Good But Your Husqvarna Won’t Turn Over or Crank

If you’re still experiencing a problem and it isn’t caused by a bad starter solenoid, check the battery, cables, starter switch, and safety switches.

Read more in my article about items to troubleshoot when your Husqvarna zero-turn won’t turn over or crank.

Husqvarna Lawn Mower Won’t Start After Getting Wet

Another reason why your mower may not start is due to water in the electrical system. Check out things that can keep your mower from starting after you leave it in the rain for more information.

Still Having Problems with Your Husqvarna Lawn Mower?

If you are still having problems with your mower, check out my guide on common problems owners encounter with their lawn mowers.

I put together a chart to identify causes and solutions to problems including starting, smoking, cutting, vibrating, dying, and more.

You can find this guide at Common Husqvarna Lawn Mower Problems & Solutions.

If you don’t feel comfortable troubleshooting and performing repairs on your lawn mower, it’s best to contact your local Husqvarna dealership or lawn mower repair shop for assistance.

You must remain safe and only perform repairs you are mechanically able to perform to avoid injury or further damage to the mower.