Skip to Content

Is Your Craftsman Starter Solenoid Bad? (Troubleshoot)

You attempt to start your mower and the engine won’t turn over. You just hear a humming or clicking sound.

A Craftsman starter solenoid is likely bad when the solenoid is bypassed and the starter motor turns over the engine. A starter solenoid that is mounted on the starter can be tested using a battery charger to determine whether the solenoid is bad.

Take caution when working with the starter solenoid. Follow all safety precautions listed in your Craftsman operator’s manual.

Lawn mower starter solenoid

This post may include affiliate links. Purchases made through these links may provide a commission for us, at no extra cost to you. As an Amazon Associate, we earn from qualifying purchases.

Follow all safety instructions provided in your equipment operator’s manual before diagnosing, repairing, or operating. Consult a professional if you don’t have the skills, or knowledge or are not in the condition to perform the repair safely.

What Is a Craftsman Lawn Mower Starter Solenoid? 

A Craftsman lawn mower solenoid is like an on/off switch. It is an electromagnet switch that is actuated to engage the starter motor to turn over the engine.

The starter solenoid is usually mounted to the starter motor, but it doesn’t need to be to work correctly. Some lawn mower solenoids can be found mounted closer to the battery than the starter. 

Three & Four Post Solenoids 

This is a typical wire schematic of three and four-post solenoids. Remember, not all wire schematics are the same for every lawn mower.

Some schematics will include wiring for options like lights and 12-volt ports on some Craftsman mowers. These diagrams only show the basic wiring schematic. 

How to Identify Craftsman Lawn Mower Solenoid? 

Solenoids can appear a little differently. Some may be round while others are square. It may have 3 or 4 posts sticking out of it. Some solenoids will be attached at the top of the starter.

The positive (+) wire from the Craftsman battery attaches to one side of the solenoid. Following the positive cable from the battery is an easy way to find your solenoid.  

You will find solenoids on every Craftsman mower with an electric start engine.  

What Causes a Craftsman Lawn Mower Starter Solenoid to Go Bad? 

A Craftsman solenoid is an electrical switch. Electrical items can fail at any time.

Inside the solenoid, you will find a spring and copper plate. A Craftsman starter solenoid can go bad if the spring gets weak or the copper plate starts to corrode.

The solenoid can also fail as a result of a weak starter, bad battery, or bad ground.  

It is good to know what to look for when you are diagnosing a solenoid. 

Symptoms of a Bad Craftsman Starter Solenoid on Lawn Mower 

  • Clicking or humming sound when you turn the ignition key and the mower doesn’t start.
  • The wire gets hot and begins to smoke or melt.

Steps to Diagnose a Bad Craftsman Lawn Mower Solenoid 

List Tools Needed: 

  • Volt-Ohms Meter 
  • Screwdriver 
  • Continuity Light
  • Wrenches to check for loose wires 
  • Needle Nose Pliers (If screwdriver does not work) 
  • Battery Charger (Optional) 

If you are going to diagnose the solenoid on your lawn mower, there are a few ways to do so. 

1. Make Sure Your Battery Has a Full Charge

Use your voltmeter to make sure your battery has at least 12.3 volts in it. Read more about testing your battery in our article 5 Reasons Your Craftsman Mower Battery Keeps Dying.

2. Get Your Mower Ready to Start

  • Set the parking brake
  • Make sure your lawn mower is in neutral
  • Turn the key to the on position

3. Bypass the Starter Solenoid Using a Screwdriver

Lay a long screwdriver over the solenoid to touch the two cables to bypass the starter. The two cables you are looking for are the cable from the battery and the cable to the starter.

It may throw a spark when the screwdriver makes contact with the wires. This is common so don’t be alarmed.

If the engine happens to turn over while you have your solenoid bypassed there is a good chance your solenoid is bad. If the screwdriver does not work well, you can also use needle nose pliers to jump the solenoid. 

Before you replace the starter solenoid, check for loose or corroded wires or bad ground. These items can keep the solenoid from getting the power it requires to work. 

4. Test the Starter Solenoid

Solenoids that are mounted on the starter can be tested. Remove the starter from the engine and test the solenoid with a battery charger. This is a good way to watch if the starter is working with the solenoid. 
 
Once the starter has been removed from your lawn mower, you need to attach the negative (-) clamp to the case of the starter and touch the positive (+) clamp to the big post and exciter wire on the solenoid. This is just a quick bench test when the starter is out. 

Can You Bypass a Craftsman Lawn Mower Starter Solenoid? 

A Craftsman starter solenoid can be bypassed by placing a long screwdriver across the solenoid from touching the cable from the battery to the cable to the starter.

Be careful. The connection could cause a spark which is normal. Always wear safety gear.

Mower Won’t Start After Leaving in the Rain

Another reason why your mower may not start is due to water in the electrical system. Check out Why Your Mower Won’t Start After Leaving in the Rain for more information. 

Craftsman Mower Clicks But Won’t Turn Over or Start

When you hear a clicking or humming sound and you can’t get your Craftsman to start, it is often caused by a bad starter solenoid. However, there are several other items that can cause this to happen.

Check out this article on a mower clicking and not starting here.

Still Having Problems With Your Craftsman Lawn Mower?

It would be nice to own a mower that will never give you problems. However, they don’t exist. Own a lawn mower long enough that you are bound to run into problems.

The most common of them are problems with starting, smoking, dying, vibrating, and cutting.

I put together a handy guide to help you quickly identify items that can cause a problem in your riding mower, zero turn, and push mower along with ways to solve them. You can find this guide at Common Craftsman Lawn Mower Problems & Solutions.

If you are unsure how to safely perform diagnostics and repairs on your lawn mower, it’s best to have a professional complete the repairs.

This will help you avoid personal injury or additional damage to the mower. Your local lawn mower dealership or lawn mower repair shop will be able to help you solve your problem.