Skip to Content

Husqvarna Mower Clicks But Won’t Start or Turn Over (FIXED)

It’s frustrating when you go to start your mower and all you hear is a clicking or humming sound. I’ve put together a list of items to troubleshoot to get your mower running again.

A Husqvarna lawn mower clicks and won’t start or turn over when the wires and cables are loose or corroded; the battery is weak; the ground is bad; the starter solenoid is bad, or the starter motor has failed.

Take all safety precautions listed in your Husqvarna operator’s manual. Consult a professional mechanic if you don’t feel comfortable working on your mower’s electrical system.

Reminder: Always disconnect the negative cable (black) from the battery before making any repairs to the electrical system.

Battery causes Kubota lawn mower to click

This post may include affiliate links. Purchases made through these links may provide a commission for us, at no extra cost to you. As an Amazon Associate, we earn from qualifying purchases.

Follow all safety instructions provided in your equipment operator’s manual before diagnosing, repairing, or operating. Consult a professional if you don’t have the skills, or knowledge or are not in the condition to perform the repair safely.

5 Reasons Husqvarna Mower Clicks But Won’t Start or Turn Over

1. Damaged or Loose Battery Cables, Wiring & Terminals

With the constant vibration of the mower, the cables can become loose. Check the cable, wiring, and terminals before checking the condition of the battery.

  • Make sure the cables from the battery to the solenoid and from the solenoid to the starter motor are securely attached.
  • Check the terminals and connections for corrosion that can interfere with continuity. You’ll need to remove any corrosion buildup you find.

To reduce corrosion in the future, make sure your mower is dry before storing it in a dry location.

SOLUTION: Replace any cables or wiring that keep coming loose or are broken. Bad cables on your Husqvarna mower can contribute to a bad battery and starting issues.

Disconnect the battery from the mower and remove any components that have corrosion so you can clean them.

A wire brush and a baking soda mix consisting of 2 cups of water and 3 heaping tablespoons of baking soda work well. Repair or replace any wiring that has signs of corrosion.

Add a dielectric grease to protect terminals and wiring from corrosion. Replace terminals when they are damaged or in bad condition.

2. Bad or Weak Battery

A weak battery may not provide enough power to turn over the engine to start it.

Check the battery voltage level. If it is low, place the battery on a battery charger to charge it. When you find the battery won’t hold a charge, it is bad and must be replaced.

If you find you are able to charge the battery but it just keeps dying, you may need to check the Husqvarna charging system. Refer to the charging system section near the end of the article.

Check the voltage of the battery

Use a multimeter’s red and black prongs and touch them to the terminals of the same colors. Most batteries used on a Husqvarna mower are 12 volts.

On a 12-volt battery, you may get a voltage reading between 11.5 and 12.7. A battery that is almost dead will register closer to 11.5V while a battery that is fully charged will read 12.7V.

Charge a lawn mower battery

  • Put on your safety gear so your eyes and skin are protected from acid or electrical shock.
  • Get access to the battery and its terminals. You may need the screwdriver to uncover the lawn mower’s body to get access to the battery or battery casing.
  • Leave the battery in its casing with the terminal cables attached.
  • Connect the charging cables starting with the red cable first (The one with the positive sign on it)
  • The red cable clamp goes onto the positive terminal, and the black cable clamp goes on the negative battery terminal.
  • Make sure that your skin only touches the rubber coating of the charging cables and clamps.
  • Set the charger’s voltage level and amp level to the desired level. The average volt level for a lawn mower is usually 12 volts. More amperage charges the battery faster (Start with two amps and work up to no more than 10 amps).
  • If your charger has a battery charging gauge, keep the charger connected until the battery is fully charged.

SOLUTION: When the Husqvarna battery is weak, use a battery charger to charge it. If you find the battery will no longer hold a charge, it’s time to replace it with a new battery.

If the battery is able to be sufficiently charged using a battery charger, but you continually find it dead when you go to use your Husqvarna, you should look for a problem with the charging system.

3. Bad Ground

Check the black ground cable that runs from the battery to the frame on your Husqvarna. It must make good contact and be free of corrosion.

You also need to check the ground from the solenoid. A 3-post solenoid is self-grounded.

SOLUTION: Replace a damaged ground cable. Remove any corrosion found for the grounds from the battery and the starter solenoid.

4. Bad Starter Solenoid

After you have confirmed the battery, cables, and connections are in good condition, move on to checking the starter solenoid. This is often the problem when you hear a clicking or humming sound and your mower doesn’t start.

The solenoid acts like an on-off switch. It is an electromagnet switch that is actuated to engage the starter motor so the engine will turn over.

Most starter solenoids are mounted on the starter. However, they do not have to be to still work. Follow the positive wire from the battery to find the solenoid.

There are many reasons why a Husqvarna starter solenoid can go bad. The internal spring can become weak or the copper plate can start to corrode.

A bad ground, weak starter, or bad battery can also result in the starter solenoid failing.

SOLUTION: Test your starter solenoid. You’ll need a volt-ohms meter, screwdriver, continuity light, and some wrenches.

Click here to find instructions on troubleshooting your Husqvarna starter solenoid. If you are able to start your mower by bypassing the solenoid, it must be replaced.

5. Bad Starter Motor

If you’ve checked the battery, cables, wiring, ground, and starter solenoid only to find them in good condition, but still have a starting problem, your starter may be the problem. The starter can be removed and tested.

SOLUTION: A starter can be a pricey item on a lawn mower. I advise having your local dealership confirm you have a starter motor problem before you replace it.

You can also bring the starter to a local repair shop that specializes in starter and alternator repairs to have the starter tested.

Related Topic:

Bad Charging System Drains the Battery

A bad charging system on a Husqvarna mower will not keep your battery charged and in turn cause a weak battery to not start your mower.

Perform the steps provided here to check the charging system using a volt-ohms meter.

If you find your Husqvarna lawn mower is no longer charging the battery, I recommend having a mechanic familiar with your charging system perform further tests and necessary repairs.

Troubleshooting the exact cause of a charging system can be quite difficult.

If you’re not familiar with the charging system, you will probably just end up throwing parts at your mower.

This can get very expensive, especially since if you get it wrong, you can’t return an electrical part. You could be looking at a bad stator/alternator, regulator, or other electrical problem.

Still Having Problems with Your Husqvarna Lawn Mower?

If you are still having problems with your mower, check out my guide on common problems owners encounter with their lawn mowers.

I put together a chart to identify causes and solutions to problems including starting, smoking, cutting, vibrating, dying, and more.

You can find this guide at Common Husqvarna Lawn Mower Problems & Solutions.

If you don’t feel comfortable troubleshooting and performing repairs on your lawn mower, it’s best to contact your local Husqvarna dealership or lawn mower repair shop for assistance.

You must remain safe and only perform repairs you are mechanically able to perform to avoid injury or further damage to the mower.