Skip to Content

Too Much Oil in a Kubota Lawn Mower (This Happens)

You frequently check the engine oil level to make sure it doesn’t get too low and damage the engine. However, did you know adding too much oil can also cause engine damage?

Too much engine oil in a Kubota lawn mower may cause engine damage due to overheating, seal damage, blown gaskets, or a hydro locked engine.

You may be able to easily fix your problem by correcting the engine oil level, but it may not be that simple. The pressure that builds inside the tank can potentially cause engine damage.

Before troubleshooting your engine problem, remove the spark plug boot(s) and wait for the engine to cool.

Too much oil in a Kubota mower

This post may include affiliate links. Purchases made through these links may provide a commission for us, at no extra cost to you. As an Amazon Associate, we earn from qualifying purchases.

Follow all safety instructions provided in your equipment operator’s manual before diagnosing, repairing, or operating. Consult a professional if you don’t have the skills, or knowledge or are not in the condition to perform the repair safely.

5 Effects of Too Much Engine Oil in a Kubota Lawn Mower

1. Engine Seal Damage on an Engine

Pressure in the crankcase will build when you pour too much engine oil into the crankcase. This pressure may blow out the seals causing oil to leak from the engine.

If you don’t find the oil leak quickly enough, you may end up with a blown engine because you ran it out of oil.

When you run the engine low on oil, heat will build in the engine. The heat can become so intense that it can spin a rod or weld it to the crankshaft.

The excessive heat can also break the rod and send it out of the engine block. The piston can weld itself to the cylinder causing it to seize up.

2. Engine May Overheat

Too much oil in a Kubota lawn mower engine will not allow the crankshaft and rod to move freely because they have to push through more oil.

This causes the crankcase pressure to increase and puts the internal engine parts under load.

The valve spring and rocker arm will get hot. The oil might not flow properly which can create more heat. Aluminum, the material most engines are built with, gets very hot intensifying the problem with your Kubota mower overheating.

The engine can get so hot it can pop out a valve guide or a valve seat from the engine block. If this happens to your engine you will need to have your engine scraped out by an experienced small engine mechanic.

3. Engine May Lock Up

Too much oil can find its way into the cylinder making the engine turn over very hard. If the oil gets past the rings, due to wear, it could lock up the engine. This is what is known as hydro locked.

The combustion chamber, which should only have air and a small amount of fuel in it, now has oil in it.

When adding compression, the piston cannot compress the oil and it becomes hydrolocked. There is a good possibility the piston will bend when you go to start the engine.

4. Engine May Not Run Well and Smoke

Sometimes when there is too much oil in your engine it will run, but not very well. Too much engine oil can get up to the spark plug and foul out the plug.

The oil inhibits the spark that is needed to fire the fuel properly.

Another reason why your lawn mower may not run well is that oil can find its way into the valve train. This oil gets burned in the cylinder and you will find yourself in a thick cloud of whitish blue stinky smoke.

In addition to the smoke, when the air filter becomes clogged, the engine may pull air and oil out of the crankcase.

5. Engine May Blow Gaskets

The engine problems you experience with a Kubota push mower, riding mower, and zero-turn mower are mostly the same. The excessive heat from overfilling with oil may blow gaskets.

Replacing gaskets on a twin-cylinder engine is more expensive than repairs on a push mower engine because you will have to remove the engine from the lawn mower resulting in additional labor costs.

In Summary

Adding a little additional oil may not seem like a big deal, but it is actually a huge deal that can result in requiring a significant repair or an engine replacement.

So when doing oil changes or adding oil check twice and only add what is required by your engine manufacturer. Don’t assume going over the required amount will be okay.

Don’t continue to run your Kubota when you notice engine problems. Consult an experienced small engine technician when you experience engine problems that aren’t able to be fixed with a simple oil change or engine repair.

The technician can perform tests on the engine to determine if it is repairable or if it should be replaced.

How to Remove Excess Oil From a Kubota Lawn Mower

If you overfilled your engine oil, you need to get the oil down to the correct level. The first thing you need to do is remove the spark plug wire for safety. There are several different ways to remove engine oil from your Kubota mower.

  1. Drain Plug or Valve Port: You need to find the drain plug or valve port on the engine if your lawn mower has one. It may be found on the side of the engine by the dipstick or at the bottom of the oil pan under the lawn mower.

    Have your drain pan ready to collect the oil. Remove the plug for a quick second and replace it. Check your oil level.
  2. Oil Filter: If your engine uses an oil filter, you can drain a little oil by loosening or removing the oil filter to drain a little oil. Have a rag ready to collect the oil.
  3. Fill Hole: Your mower may not have a drain plug or oil filter. Many small engines on push mowers do not have a drain plug and you have to tip the mower over to drain a little oil out of the fill hole.
  4. Oil Extractor Pump: An oil evacuator works well to remove oil. An extractor will remove oil through a tube inserted into the engine oil fill hole.
  5. Turkey Baster: A turkey baster works well for removing small amounts of oil. Just make sure you don’t reuse it for cooking purposes after using it in your engine. These are pretty inexpensive to replace.

How to Not Overfill Oil in a Kubota Lawn Mower

Before you change your lawn mower’s engine oil you need to look at your owner’s manual to find your engine oil capacity.

If you don’t have your owner’s manual, you can always use Google or the search engine of your choice to find the crankcase capacity.

Most small engines on push mowers will take about 3/4 of a quart of motor oil. A v-twin gas-powered engine will usually take approximately 2 quarts.

A larger lawn mower commercial engine known as a big block can take 3 quarts of engine oil. These larger engines are known to be about 34 horsepower or larger.

The best way not to overfill your engine oil is to know your crankcase capacity and only add 1/2 quart of oil at a time. Keep checking the oil until you hit your mark.

If you are adding 1/2 quart at a time, when you get close to being full, just add a little bit at a time and check the oil level on your oil gauge or dipstick.

Will Too Much Oil Prevent a Kubota Lawn Mower from Starting?

Too much engine oil can prevent your Kubota engine from running. The oil pan on the small engines used on lawn mowers is very small.

There is not much room for error with such a small space. If you put too much oil in an engine your engine can hydrolock.

Hydrolocking is when oil gets up into the cylinder and past the piston. The oil then fills up the combustion chamber not allowing the piston to move to the top of the combustion chamber.

The piston is designed to compress air and not oil or water. When you pull on the rope or start the engine with a starter the oil will not compress and it won’t let the piston move. This is referred to as being hydrolocked.

Too much oil can also foul out the spark plug and not allow the engine to run. Another damage too much oil can do to an engine is oil getting into the carburetor through the valve train causing the engine not to run.

This oil can pass through the carburetor and into the air filter which will also cause your engine not to run.

Still Experiencing Problems with Your Kubota Lawn Mower?

Own a lawn mower long enough, you’ll start running into problems with it starting, not continuing to run, smoking, leaking gas, giving a bad cut, vibrating, or another issue.

To help you save time and money, I have put together a guide to help you troubleshoot the next problem that develops on your Kubota mower.

You can find this guide at Common Kubota Lawn Mower Problems & Solutions.

If you are unsure how to perform diagnostics and repairs on your Kubota lawn mower safely, it’s best to have a professional complete the repairs.

This will help you avoid personal injury or additional damage to the mower. Your local Kubota lawn mower dealership or lawn mower repair shop will be able to help you solve your problem.