Skip to Content

16 Reasons a Westinghouse Generator Won’t Start: SOLVED!

Many homeowners have a generator on hand in case there is a power outage. If you are one of these people, it can become increasingly frustrating when the generator won’t start during a time of extreme need.

A Westinghouse generator won’t start due to a plugged air filter, wrong choke setting, faulty on/off switch, empty fuel tank, plugged fuel filter, clogged fuel line, dirty carburetor, bad spark plug, bad spark arrestor, low engine oil, or faulty fuel cap.

Check the battery, starter solenoid, and ignition switch on models with an electric start.

Place the generator on a flat level service, remove the spark plug wire, and wait for the engine to cool prior to performing repairs. Refer to your Westinghouse operator’s manual for safety precautions.

Westinghouse generator won't start

This post may include affiliate links. Purchases made through these links may provide a commission for us, at no extra cost to you. As an Amazon Associate, we earn from qualifying purchases.

Follow all safety instructions provided in your equipment operator’s manual prior to diagnosing, repairing, or operating. Consult a professional if you don’t have the skills, or knowledge or are not in the condition to perform the repair safely.

Westinghouse Generator Won't Start Infographic
Westinghouse Generator Starting Problems

Reasons Your Westinghouse Generator Won’t Start

Empty Fuel Tank on a Westinghouse Generator

A Westinghouse generator has a small fuel tank. You may have forgotten the last time you added fuel or your fuel gauge no longer works and provides you with a sufficient reading.

I only mention this obvious cause of a starting problem because it’s easy to skip checking the fuel level when you’re frustrated.

SOLUTION: Add fresh gasoline to the fuel tank.

Bad or Old Fuel in a Westinghouse Generator

Many people don’t realize gas degrades and starts to become less effective as it sits for long periods of time. This can begin to happen as soon as 30 days after purchase.

Ethanol, used in most gasoline, attracts moisture to the fuel system. As this ethanol and water mixture evaporates it leaves behind a varnish that can cause component failure and fuel restrictions.

Because of the adverse effects ethanol has on a Westinghouse generator, it’s important to keep these things in mind when purchasing, storing, and consuming fuel:

  • Purchase fresh fuel with a minimum 87 octane rating (91 RON).
  • Never use gas with more than a 10% ethanol content. Ethanol-free fuel is best.
  • Consume fuel within 30 days.
  • Use a fuel stabilizer if you are unable to consume it within 30 days to make it last a little longer without breaking down. (Fuel stabilizer must be added to fresh fuel. It will not reverse the effects of old fuel).
  • Store fuel in an approved fuel container away from moisture or combustible products.

SOLUTION: If you find old fuel in your Westinghouse generator, drain the fuel using a fuel siphon pump. Mix fresh gas with a fuel additive to help clean the fuel system, reduce moisture and stabilize the gas.

Add the gas to the fuel tank. Once you are able to get the generator to start, allow it to run for about 15 minutes so the gas and stabilizer mixture is able to work its way through the fuel system.

I like a product called Sea Foam Motor Treatment. I use this product in every tank of gas to help reduce the issues that can result from using fuel with ethanol. Another good option is STA-BIL.

Read more about the right fuel to use in a Westinghouse generator along with storage tips here.

Plugged Fuel Filter on a Westinghouse Generator

To keep dirt and contaminants that get into the fuel tank out of the fuel system, a fuel filter is used on a Westinghouse generator.

The fuel filter is a maintenance item that Westinghouse recommends replacing every 6 months or after 100 hours. When this filter isn’t replaced regularly it can become plugged.

A plugged filter will prevent a good flow of fuel from passing through the filter. The engine won’t get enough fuel to start and run.

Some models will use a fuel valve with a sediment bowl. This bowl should be cleaned out annually.

SOLUTION: Replace a plugged Westinghouse inline fuel filter.

Clogged Fuel Line on a Westinghouse Generator

The gummy deposits or dirt left behind by old fuel can clog the fuel system including the fuel line. Check for clogs in the fuel line that could be restricting fuel to the engine.

SOLUTION: If you find a restriction in the fuel line, remove the line from the generator. Spray carburetor cleaner to loosen the clog and blow compressed air to the line to remove it.

If you are unable to remove the fuel restriction, replace it with a new fuel line.

Dirty Carburetor on a Westinghouse Generator

Air and fuel are ignited to start the engine and keep it running. The carburetor is the component that is responsible for regulating the amount of gas that mixes with air for combustion.

When the carburetor fails because the fuel passageways become clogged from old fuel, gas isn’t able to get to the cylinder and the generator won’t start.

SOLUTION: Once you have verified you are getting gas to the carburetor, but not getting gas to start the generator, remove the carburetor.

Clean it with a carburetor cleaner to remove varnish and deposits forming in the carburetor. Take a look at the carburetor float, float needle, and fuel jets to make sure they are sufficiently clean and in good condition.

If you find any damaged parts, you must replace them using a carburetor rebuild kit or a replacement carburetor.

Plugged Air Filter on a Westinghouse Generator

Like the fuel filter, the air filter is another maintenance part installed to keep dirt and debris from entering through the air intake. This is to protect the engine from damage that can be caused by just a small amount of dirt.

You must always run an air filter on your Westinghouse generator. This filter should be checked several times throughout the year to clean it and ensure it is in good condition.

I recommend starting each year out with a new air filter. Maintenance doesn’t stop there. The filter needs to be regularly checked and cleaned to keep it in good condition.

A very dirty filter not only may keep the generator from starting, but it can also cause it to overheat and potentially cause permanent engine damage.

SOLUTION: If you find your air filter is plugged, follow the instruction below to clean a foam filter. If you are unsure of the type of filter you have and its cleaning procedure, consult the Westinghouse operator’s manual.

Clean a Westinghouse generator foam-style air filter

  • Remove the air filter from the housing.
  • Wipe out any dirt remaining in the air filter housing and cover. Don’t allow dirt to fall into the air intake.
  • Inspect the foam filter for damage and replace it if needed.
  • If the filter is in good condition, clean it with a mild detergent and water solution.
  • Rinse the filter until the soap is removed.
  • Squeeze the filter and allow it to dry. Don’t wring the filter as you may tear it.
  • IF THE FILTER WAS COATED IN OIL, once dry, coat the filter with clean engine oil. Squeeze to remove excess oil. Not all foam filters are coated in oil. Refer to your model’s operator’s manual if you are not sure whether to add oil to the filter.
  • Install the air filter.
  • Reattach the air filter cover.

Clean a Westinghouse generator paper air filter:

  • Remove the air filter from the housing.
  • Wipe out any dirt remaining in the air filter housing and cover. Don’t allow dirt to fall into the air intake.
  • Inspect the paper air filter. Tap the filter to loosen dirt so it falls from the filter. If the filter is very dirty, damaged, or no longer seals the air intake sufficiently, replace it with a new one.
  • Install the air filter.
  • Reattach the air filter cover.

Consult your operator’s manual if you are unsure what type of filter is used on your generator, how to clean it, or if your generator uses a different type of filter.

*If your primary filter uses a foam pre-filter, do not apply oil to the pre-filter. This will damage the primary filter.

Plugged Fuel Vent on a Westinghouse Generator

On most portable Westinghouse generators, the fuel tank vents out of the gas cap. Some models have an independent vent installed on top of the fuel tank. A vent is required to keep the pressure in the fuel tank equal to the atmospheric air pressure.

When air isn’t allowed to pass through the gas cap due to a plugged vent, the fuel tank will form a vacuum. This prevents fuel from getting to the carburetor and your generator will fail to start.

SOLUTION: To determine whether your gas cap is the cause of your starting problem, loosen or remove your cap to allow air inside the tank and then attempt to start the generator.

If it starts, but stops running again after you place the cap back on the generator and allow it to run for a while, you may have a problem with the cap. I recommend replacing a bad fuel cap or bad vent.

Plugged Spark Arrestor on a Westinghouse Generator

The spark arrestor screen is a metal screen on the muffler that prevents sparks and hot exhaust material from emitting from the muffler. This screen is required to prevent injuries and fires.

When it becomes plugged, the generator will have a hard time starting and running.

SOLUTION: Remove the spark arrestor screen from the muffler. Take a look at it to ensure it isn’t torn and doesn’t have any holes in the screen. If it does, the screen must be replaced with a new one.

If it doesn’t have any damage, go ahead and clean it with a small metal brush to remove soot deposits. Once clean, reinsert the screen back onto the muffler.

Bad Spark Plug on a Westinghouse Generator

A spark plug can be faulty when the tip is dirty, the porcelain is cracked or the electrode is burnt. This will cause your generator not to start because of a lack of spark.

SOLUTION: You can clean the spark plug to remove the deposits on the tip. If your spark plug tip is very dark in color or damaged, you must replace it with a new one.

The spark plug needs to be properly gapped following the manufacturer’s specifications as found in the operator’s manual. Starting problems can be caused by a spark plug that is gapped incorrectly or a spark plug wire that is loose.

Bad Ignition Coil on a Westinghouse Generator

Before checking for a bad ignition coil, make sure your spark plug is in good condition. The ignition coil provides voltage to the spark plug so it can start the engine.

If the spark plug isn’t able to fire due to a bad spark plug or ignition coil, the engine will not start.

SOLUTION: Check the continuity of the ignition coil using an ohm meter. If you find a break in the continuity, replace the ignition coil.

Incorrect Engine Oil Level in a Westinghouse Generator

A Westinghouse generator will not start when the engine oil is not at the correct level. The generator has a sensor that recognizes a low engine oil level. It will prevent the engine from running with a low engine oil level.

SOLUTION: To check the engine oil level, begin by placing the generator on a flat-level surface. Remove the oil fill cap and wipe off the dipstick with a clean cloth to remove the oil.

Reinsert the dipstick into the oil-fill tube, but don’t screw on the cap. Remove it and look at the oil level on the dipstick. Ensure it is in the full range on the dipstick.

If it is not, correct the engine oil level by removing or adding a little oil until it is at the correct level.

When you find you have the correct engine oil level and the low oil sensor stays on, you may have a faulty sensor. It’s best to take the generator to a Westinghouse service center to be repaired.

Bad Choke Dial/Switch or Wrong Choke Setting on a Westinghouse Generator

Some Westinghouse generator models use an OFF-RUN-CHOKE dial or switch. It may be faulty and no longer functions correctly.

This bad dial or switch on a generator will keep the generator from starting if it is no longer adjusting the choke when switching it between the choke/start and on positions.

Other Westinghouse generator models will use a choke lever to manually adjust the choke. In this case, the choke lever must be placed in the choke position to start a cold engine.

It will then need to be adjusted to the off position so the engine receives enough air to keep running.

SOLUTION: Have a service center identify if the problem is in the dial. Check for a stuck choke plate that may be preventing the generator from starting with the dial or manual choke lever in the correct position.

Bad Recoil on a Manual Start Westinghouse Generator

When the starter recoil wears or parts of the recoil break, it’s hard or impossible to get the generator started. The rope on the recoil can become unstrung or the pulley, springs, or clips may break causing your starting problems.

SOLUTION: Sometimes, restringing the recoil is all you need. Other times you will have to replace broken parts in your recoil. Before replacing parts, price out a full recoil replacement.

Depending on the price difference, it may be better to replace the recoil assembly over tearing it down and replacing broken components.

Bad Ignition Switch on a Westinghouse Generator (Electric Start)

The ignition switch can go bad on a generator with an electric start preventing it from starting. When the electric start isn’t working, use the manual recoil to start the generator until you are able to get it fixed.

SOLUTION: Test the switch using a multimeter and replace it if necessary.

Bad Battery on a Westinghouse Generator (Electric Start)

Make sure the battery is charged. If it has a low charge, you can attempt to charge the battery. If it won’t hold a charge, it’s time to replace the battery with a new one.

Check the cables and wiring to make sure you have good continuity and making good connections.

SOLUTION: Check the voltage of the battery and charge it if it is weak. Replace a dead battery or one that won’t hold a charge.

Bad Starter Solenoid on a Westinghouse Generator (Electric Start)

You may hear a clicking or humming sound when you press the ignition switch button or turn the key (depending on your model) and your generator won’t start. Or, you may find the wiring is getting hot and beginning to smoke.

These are indications the solenoid may be bad. A starter solenoid goes bad when the internal spring gets weak or the copper plate begins to corrode. A weak starter, bad battery, or bad ground can also be the reason for the solenoid failure.

SOLUTION: You can attempt to bypass the starter using a screwdriver or pliers by touching the cable from the battery and the cable to the starter.

Be careful as it may throw a spark. If the engine turns over with the solenoid bypassed, it is likely the starter solenoid is bad.

You must check for loose wires or bad ground before replacing the solenoid. These are items that can cause the solenoid to not work correctly.

The good news is most portable Westinghouse generators with an electric start have a manual starter recoil installed to pull-start it to get it running. If you are able to manually start it, you can narrow down your problem to the electric start system.